Rod and Main Bearing Clearances | Measurement, Tolerances, and Engine Inspection

6 NOVEMBER 2026

Bearing clearance is one of the dimensions that must be verified before an engine is assembled. The gap between a crankshaft journal and its bearing surface affects oil-film formation, friction, and heat dissipation. Even when new bearing shells are fitted, incorrect journal dimensions or housing geometry can leave the assembly outside its permitted tolerance. Accurate rod bearing clearance and main bearing clearance measurements are therefore essential during engine rebuilding, machining, and failure inspection.

How Bearing Clearance Affects Engine Performance

An engine’s crankshaft rotates on a film of pressurized oil that separates the journal from the bearing surface. As the journal rotates, it draws oil into a narrowing gap, generating pressure that supports the applied load.

The specified oil clearance must account for journal diameter, bearing geometry, oil viscosity, operating temperature, and engine speed. If the clearance is too small, the oil film may become inadequate under certain conditions, increasing the risk of overheating and surface damage. Excessive clearance can increase oil leakage and contribute to low oil pressure.

A commonly used preliminary guideline for rod bearing clearance is approximately 0.001 inch of clearance per inch of journal diameter. However, this is only a general rule of thumb. Always follow the engine manufacturer’s specifications to determine the acceptable range.

Main Bearings and Rod Bearings: What Needs to Be Checked?

Main bearings sit between the engine block and the crankshaft’s main journals. They support the crankshaft and maintain its position within the block. The required main bearing clearance must be verified at each journal because wear, housing dimensions, and bearing tolerances can vary.

Connecting rod bearings sit between the connecting rods and crankshaft crankpins. They experience changing loads as the pistons move through their operating cycles. Their clearance must be checked separately rather than assumed to match the main bearings.

Both measurements contribute to correct crankshaft support, but the permitted values depend on the engine design and its service requirements.

Bearing Inspection and Clearance Verification

Before assembly, inspect bearing shells and crankshaft journals for scoring, discoloration, and uneven wear. Use an outside micrometer to measure each journal and a dial bore gauge to check the installed bearing bore.

Calculate the clearance by subtracting the journal diameter from the bearing bore diameter. 

For example, a 50.050 mm bore and a 50.000 mm journal give a clearance of 0.050 mm. Plastigage can provide an additional check when used according to the engine’s service procedure. Always compare the results with the manufacturer’s specifications before assembly.

Reading a Bearing Clearance Chart

A bearing clearance chart can help compare measured dimensions with the required limits, but the values must match the engine model and bearing arrangement.

MeasurementPurpose
Journal diameterIdentifies wear, taper, and out-of-round conditions
Installed bearing boreConfirms the assembled bearing dimensions
Calculated clearanceEstablishes the actual diametral gap
Service limitsDetermines whether the measurement is acceptable

When consulting a bearing clearance chart, check whether the figures apply to new components, used components, or specific bearing sizes. Undersize crankshaft journals may require matching undersize bearings. Never select a replacement bearing solely from a general chart without confirming the engine’s specifications.

What Happens When Clearance Is Incorrect?

A clearance problem can produce symptoms during operation, although these symptoms alone cannot confirm the cause.

Excessive clearance – Too much gap can allow more oil to escape from the bearing, contributing to low oil pressure and knocking.

Insufficient clearance – A gap that is too tight can limit the oil film and cause friction, heat, and bearing damage.

Uneven clearance – Differences across the bearing may point to a worn crankshaft journal, a distorted housing, or incorrect assembly.

If the measured crankshaft bearing clearance falls outside the specified limits, inspect the journal dimensions, bearing part numbers, housing condition, and assembly procedure before deciding on corrective work.

Wrapping It UP

Bearing clearance should be measured rather than estimated during an engine rebuild. Check each journal, verify the installed bearing dimensions, and compare the results with the correct engine specifications. These checks help identify wear and fitment problems before they damage the crankshaft or bearings.

FAQs

1. What is the difference between rod and main bearing clearance?

Rod bearings support the crankshaft crankpins at the connecting rods, while main bearings support the main journals in the engine block. Their permitted clearances may differ.

2. How is oil clearance calculated?

Subtract the crankshaft journal diameter from the installed bearing’s inside diameter. Always measure the bearing with its housing fasteners tightened to the specified torque.

3. Can I use a general bearing clearance chart?

A bearing clearance chart is useful for reference, but the engine manufacturer’s specifications should determine the final acceptable range.

4. Does tighter clearance always improve oil pressure?

No. Although tighter clearance can restrict oil leakage, insufficient clearance may cause inadequate lubrication, excess heat, and bearing damage.

5. Why is engine bearing clearance checked during rebuilding?

Measuring engine bearing clearance confirms that the crankshaft, bearing shells, and housings fit within the required tolerances before the engine is operated.